DINITROL PENETRANT LT CAVITY WAX 500ml Aerosol 1147001
DINITROL PENETRANT LT is designed for applicationon open surfaces as well as in cavities, such as doors and other parts of cars, trucks and buses. DINITROL PENETRANT LT is also designed for use on spare parts etc, which are stored for long periods or transported under very corrosive weather conditions.
Applications
DINITROL PENETRANT LT can be used for cavity applications, pre-treatment of underbodies before applying a DINITROL underbody coating. It can also be used for open and semi-open surfaces due to the reinforced film that is more mechanically resistant than other common cavity waxes.
Method of use
DINITROL PENETRANT LT is applied by spraying with manual or semi-automatic application equipment, and is suitable for either airmix or airless spraying.
Application temperature should be between 15 and 30°C.
Pre-treatment Substrates
Surface shall be clean, dry and free from loose corrosion.
Over-Coating / 2-Layer-Application
DINITROL Penetrant LT can be over-applied with any
DINITROL bitumen underbody coating. For additional information, please consult DINOL GmbH.
Storage
The product should be stored at 15 – 30°C and is then having a shelf life of 2 years in unopened original packaging.
Technical Data
Colour transparent beige
Type of film waxy
Density at 23°C 860 kg/m³
Viscosity at 23°C, (DIN 4) 18 seconds
Dry matter content 52% by weight
Flash point 40°C
Aromatic content in solvent < 1%
Recommended film thickness 60 µm
Recommended film thickness wet 150 µm
Drying time 2 hours
Heat resistance > 90°C
Low temperature adhesion - 40°C
Salt spray test 1000 hours
Penetration 50 µm gap > 30 mm
Effect on car paint none
Removability White Spirit
Available in 1 L Miniservice, 60 L Drum, 208 L Drum
Share some information about your product
Share some information about your product
Share some information about your product
DINITROL PENETRANT LT CAVITY WAX 500ml Aerosol 1147001
DINITROL PENETRANT LT is designed for applicationon open surfaces as well as in cavities, such as doors and other parts of cars, trucks and buses. DINITROL PENETRANT LT is also designed for use on spare parts etc, which are stored for long periods or transported under very corrosive weather conditions.
Applications
DINITROL PENETRANT LT can be used for cavity applications, pre-treatment of underbodies before applying a DINITROL underbody coating. It can also be used for open and semi-open surfaces due to the reinforced film that is more mechanically resistant than other common cavity waxes.
Method of use
DINITROL PENETRANT LT is applied by spraying with manual or semi-automatic application equipment, and is suitable for either airmix or airless spraying.
Application temperature should be between 15 and 30°C.
Pre-treatment Substrates
Surface shall be clean, dry and free from loose corrosion.
Over-Coating / 2-Layer-Application
DINITROL Penetrant LT can be over-applied with any
DINITROL bitumen underbody coating. For additional information, please consult DINOL GmbH.
Storage
The product should be stored at 15 – 30°C and is then having a shelf life of 2 years in unopened original packaging.
Technical Data
Colour transparent beige
Type of film waxy
Density at 23°C 860 kg/m³
Viscosity at 23°C, (DIN 4) 18 seconds
Dry matter content 52% by weight
Flash point 40°C
Aromatic content in solvent < 1%
Recommended film thickness 60 µm
Recommended film thickness wet 150 µm
Drying time 2 hours
Heat resistance > 90°C
Low temperature adhesion - 40°C
Salt spray test 1000 hours
Penetration 50 µm gap > 30 mm
Effect on car paint none
Removability White Spirit
Available in 1 L Miniservice, 60 L Drum, 208 L Drum
Share some information about your product
Share some information about your product
Share some information about your product